Select a category
Your Cart
Aldesept concentrate MD 1l - Disinfectant
✘ Out of Stock

Aldesept concentrate MD 1l - Disinfectant

14.70 лв.
  • Наличност: ✘ Out of Stock
  • Weight: 1.02
  • Article code: 593


Concentrated aldehyde preparation for high-level disinfection of medical instruments and medical equipment
Aldecept MD is intended for& ;nbsp;
-    Disinfection and cleaning of medical and dental instruments, medical equipment and laboratory glassware.
-    High level cold disinfection  of heat-resistant and heat-labile medical devices, anesthesia equipment and  endoscopes (including flexible).

Aldecept MD can be used both for manual disinfection and in all semi-automatic and fully automatic circulation procedures.
Aldecept MD is a balanced a synergistic system of aldehydes and quaternary ammonium salts that exhibits high microbial efficiency at low concentrations. The preparation does not contain formaldehyde and its active ingredients are biodegradable.  
Aldecept MD is not inactivated by organic matter. Contains corrosion inhibitors, does not damage and is compatible with various materials. It has a low allergic potential. The working solutions of the preparation are pleasantly flavored and are suitable for use up to 14 days after their preparation.

Appearance: colorless to pale yellow flavored liquidPH 1% p-p: 5.5 - 7.0
Density: 1.040 g/cm3 (20°C)  ; 

Composition of the preparation
Each 100 g of Aldecept  MD contain: Active substances: 
7.5 g  Glutaraldehyde  (CAS 111-30-8)
 15 g  Ethylene dioxy dimethanol (CAS 3586-55-8)
 2 g  Benzalkonium chloride (CAS 68424-85-1)

Isopropanol, corrosion inhibitors, nonionic surfactants, chelating agent, perfume composition.< ;/p>

Aldecept MD meets the requirements for chemical disinfectants of the European Directive on Medical products 93/42/CEE and is classified as a medical device - Class IIB.  
Spectrum of action
Aldecept MD exhibits bactericidal, mycobactericidal (including tuberculocidal), fungicidal and virucidal  (HBV/HCV/HIV) activity.

< td>Bactericidal
(Paeruginosa, S.aureus, E.hirae)< /table>

Recommended disinfection regimens
Aldecept MD is supplied as a concentrate and should be administered in compliance with recommended concentrations and exposure time  (see dosage chart).  
Bath Immersion Procedure
Use the dosing cup supplied with the Aldecept MD package and tap water to prepare the working solutions. Pour the required amount of water into the tub and gradually add the required amount of concentrate. Stir. Disassemble as much as possible and expose the openings of all tools as much as possible and immerse them in the solution.  Make sure all tool surfaces and openings are completely covered and allow the detergent to work. After disinfection, rinse and dry instruments thoroughly.
Manual cleaning and disinfection of  medical apparatus and equipment
Prepare the required working solution as described above. Use a suitable agent (towel, non-woven napkin), wet it abundantly  with the solution and wipe the surface until completely wet and let the detergent work. After exposure time, dry if necessary.
Circulation processes
Aldecept MD is suitable for all semi-automatic and fully automatic circulation processes. It is recommended in this case to pre-clean manually  of medical instruments before disinfection

Microbiological activityConcentration< /td>StandardExposure
1.0%EN 1456130 min
(C. albicans, A. niger
1.0%EN 1456230 min
< ;strong>Mycobactericidal (incl. Tbc) (M.terrae, M.avium)1.0%EN 1434860 min
Virucidal (HIV/HBV/HCV) 1.0%EN 1447660 min
Sporecidal& nbsp; (B. subtilis)10.0%EN 13704120 min
< tr>< td>High-level cold chemical disinfection of heat-labile and heat-resistant medical devices
Object of disinfectionSpectrum of actionWorking solutionExposure
Disinfection and  cleaning of medical instruments, medical equipment and laboratory glasswareactericidal, fungicidal and  virucidal

Mycobactericidal, virucidal 

10 ml/1 l)

10 ml/1 l)

30 min

60 min
Sporicidal10.00 %
(100 ml/1 l
60 min

Compatibility with other materials:
Metals: aluminum, stainless steel, copper, brass, anodized aluminum.
Synthetic materials: polyvinyl chloride, polypropylene, silicone, polyethylene, rubber, latex. Storage conditions 
In a well-closed original packaging in places protected from direct sunlight, away from heating  utensils  and open fire, at temperatures from 0 to 40º C.
In case of contact with eyes, rinse them immediately with plenty of water and seek medical help. After contact with the skin, immediately wash thoroughly with soap and water. If swallowed, do not induce vomiting, seek medical attention immediately and show the container or label.  
Treatment of waste quantities and packaging
Do not release the concentrate into the environment - see special instructions / safety data sheet.
Packaging: Tubes of 3, 5 and 10 l and vials of 1000  ml
Expiry date: 3 years


We make deliveries with the courier companies Speedy and Econt.

You always use the review option.

Attach the issued documents from the shippers to the invoice.

Deliveries are usually made within 2 working days, and we always strive to ship on the day of the order.

The delivery price will be calculated after you proceed to the order payment section!

The user can generate a purchase request for goods as a guest or after registering at (creating their own user profile). Registration is easy, takes little time, and brings the following benefits:

1. You do not need to fill in details every time you shop.
2. Every registered user has access to the history and status of their orders.
3. Every registered user can (at their choice) receive current information from at the provided email address (e.g., current promotional products).
The information in the delivery request is filled out entirely by the user, and the user can specify additional details regarding the execution of the order (time range for receiving the delivery, specific description of the delivery location, etc.). After generating a purchase request for goods, the user receives an order confirmation at the email address they provided.
4. The costs for the delivery of the ordered goods are borne by the customer. The delivery costs will be generated upon completion of the order and are paid separately from the value of the goods.
5. Payment is made by cash on delivery, postal money transfer, or bank transfer